IJSRSET calls volunteers interested to contribute towards the scientific development in the field of Science, Engineering and Technology

Home > IJSRSET151587                                                     

Experimental Investigation of Deflection Characteristics of Shaft in Mercerization Machine by Varying Diameters


Jayashri V. Chopade
  • Abstract
  • Authors
  • Keywords
  • References
  • Details
Mercerization is one of part of wet processing technology; it is the special type of treatment for cotton. Mercerization is done to get some special properties of the textile materials. In this process, the physical properties of the material get change. The purpose of this work is to study the effect of deflection of mercerization machine shaft and determine how shaft stiffness affects in mercerization process. The Simulation and experiment has shown that the residual stress on the shaft deformation accounts for about 7 mm, which cannot be ignored. The control of the potential error from residual stress in the process of shaft deflection measurement is of great significance for improving the shaft deflection accuracy. The design parameters were optimized with the help of ANSYS with the objective of minimizing the internal diameter of shaft. The design optimization also showed significant potential improvement in the performance of shaft. The results of ANSYS are used for determination of deflection characteristics, modeling and analysis of mercerization machine shaft.

Jayashri V. Chopade

Mercerization Machine Shaft, Stiffness, Deflection and Bending

  1. Liang Heng-chang, Zhou Guo-qing, Liao Bo, Liu Zhi-qiang, Zhou Jin-sheng, Zhao Guang-si, Shang Xiang-yu, Zhang Hou-quan, “In-site monitoring and analysis of shaft lining’s additional strain in failure and formation grouting,” Procedia Earth and Planetary Science, 2009, 503–511.
  2.  A. Vaziri, H. Nayeb-Hashemi, “A theoretical investigation on the vibrational characteristics and torsional dynamic response of circumferentially cracked turbo-generator shafts,” International Journal of Solids and Structures, 2006, 4063–4081.
  3. G.S. Zhao, G.Q. Zho , G.R. Zhong, F.P. Zhu H.C. Liang. “Analysis of stratum grouting influence on shaft lining stress with the methods of simulation and in site measurements,” Procedia Earth and Planetary Science, 2009, 497–502.
  4. Zhou Jie, Zhou Guo-qing , Shang Xiang-yu, Li   Ting. “Numerical simulation on shaft lining stresses analysis of operating mine with seasonal temperature change,” Procedia Earth and Planetary Science, 2009, 550–555.
  5. Wang Yan-sen, Yang Zhi-jiang , Yang Wei-hao, “Viscoelastic analysis of interaction between freezing wall and outer shaft wall in freeze sinking,” Procedia Earth and Planetary Science,2009, 612–620.
  6.     C. Slater, S.R. Otto and M. Strangwood, “The quasi-static and dynamic testing of damping in golf clubs shafts fabricated from carbon fibre composites,” Procedia Engineering,2010, 3361–3366.
  7. Bhaumik S.K. “Fatigue failure of a hollow power                transmission shaft”, Engineering Failure Analysis., 9,457–467, 2002.
  8.  Goksenli A.and Bakshi Y. “Failure analysis of an elevator drive shaft”, Engineering Failure Analysis., 16, 1011–1019, 2009.
  9.  Atxaga G. and Chidera S. “Failure analysis of the end      of a shaft of an engine’, Engineering Failure Analysis., 17,714–721, 2010.

Publication Details

Published in : Volume 1 | Issue 5 | September-October - 2015
Date of Publication Print ISSN Online ISSN
2015-10-30 2395-1990 2394-4099
Page(s) Manuscript Number   Publisher
415-418 IJSRSET151587   Technoscience Academy

Cite This Article

Jayashri V. Chopade, "Experimental Investigation of Deflection Characteristics of Shaft in Mercerization Machine by Varying Diameters ", International Journal of Scientific Research in Science, Engineering and Technology(IJSRSET), Print ISSN : 2395-1990, Online ISSN : 2394-4099, Volume 1, Issue 5, pp.415-418, September-October-2015.
URL : http://ijsrset.com/IJSRSET151587.php