Approximate Representation and Exposition of ISI Flat Plate Collector including Revised Flat Plate Collector : A Review

Authors

  • Dr. Rajeshkumar U. Sambhe  Professor and Head (Mechanical Engineering), Jawaharlal Darda Institute of Engineering and Technology, Yavatmal, Maharashtra, India
  • Dr. Sagar S. Gaddamwar  Assistant Professor (Mechanical Engineering), Jawaharlal Darda Institute of Engineering and Technology, Yavatmal, Maharashtra, India

DOI:

https://doi.org//10.32628/IJSRSET207275

Keywords:

ISI Flat Plate Collector, Induced flow, Absorber Plate, Buoyancy, Thermo-Siphon

Abstract

Cosmic power is one of the numerous renewable energy sources that can use in a Photovoltaic (PV) system or Thermal. Solar collectors play a crucial role in solar thermal systems. They convert solar radiation into heat and transfer the heat to working fluids Such as water or air. The Flat-plate collectors are the numerous common type of solar collectors and typically used as a water heater or air heater. These collectors have low efficiency and low outlet temperature. Recently, many scientists have attempted to improve the efficiency and performance of flat-plate collectors via different methods. This review paper describes the results of the experimentation carried out to study and compare the performance of the modified flat plate collector having increasing riser tube diameter and reducing riser tube length with the conventional ISI marked solar liquid flat plate collector. To study, the comparative performance characteristics of a modified flat plate collector with ISI flat plate collector operated under natural circulation mode. The suggested design found to be better than the existing ISI design of the absorber plate from an efficiency point of view. The actual useful heat gain (Qu) in the suggested design understudy found to be more by 30% than that in the case of ISI collector. However, the modified flat plate collector found to operate at a relatively lower exit temperature than the conventional ISI marked collector.

References

  1. Raj Thundil Karuppa R., Pavan P. and Reddy Rajeev D.(2012), “Experimental Investigation of a New Solar Flat Plate Collector”, Research Journal of Engineering Sciences, ISSN 2278 – 9472, Vol. 1(4), pp.1-8.
  2. Dr. Karima E. Amori and Nooraddin Saad Jabouri (2012), “Thermal Improvement Of Solar Hot Water System Using Accelerated Riser In Flat Plate Collector” The Iraqi Journal For Mechanical And Material Engineering, Special Issue (B), ISSN 1726-6742, Vol 9, No 1, pp.244-257.
  3. Fatigun A.T., Adesakin G.E, Gwani M.,(2012) “Experimental determination of the effect of tube spacing on the performance of a flat plate solar collector” International Journal Of Environmental Sciences, ISSN 0976 – 4402, Volume 3, No 1, pp. 363-370.
  4. Dr. S. V. Prayagi, Dr. S. B. Thombre (2011), “Parametric Studies on Buoyancy Induced Flow through Circular Pipes in Solar water heating system”, International Journal of Engineering Science and Technology (IJEST), ISSN : 0975-5462, Vol. 3 No. 1 Jan 2011, pp. 616-627.
  5. Nandurkar, Y.Y. and Shelke R.S. (2012), “Performance and analysis of ISI flat plate collector with modified flat plate collector” International Journal of Engineering Science and Technology, ISSN 2319-1163, Vol-4, pp. 944-946.
  6. D. C. Larson (1980), “Optimization of Flat-Plate Collector-Flat Mirror Systems” Department of Physics and Atmospheric Science, Drexel University, Philadelphia, Vol.24 Issue 2, pp. 203-207.
  7. Govid N.K. Kulkarni, Shireesh B. Kedare, Santanu Bandyopadhyay. (2007). ‘Determination of Design space and optimization of solar water heating systems’, Solar Energy Elsevier Ltd. Vol.81, pp. 958-968.
  8. Amrutkar S.K., Ghodke S. and Patil K. N. (2012), “Examination of Solar Flat Plate Collector Analysis”, International Organization of Scientific Research (IOSR) Journal of Engineering, ISSN 2278-1684, Vol-2, pp- 207-213.
  9. Ljiljana T. Kosti´c, Zoran T. Pavlovi´c (2012), “Optimal position of Flat Plate Reflectors of Solar Thermal Collector”, Energy and Buildings 45, ISSN: 0378-7788, pp. 161–168.
  10. B. K. Gond, S. Mittal, P. Prajapati, R. Khare (2016), “Analysis of Solar Flat Plate Collector”, International Journal of Research and Scientific Innovation (IJRSI), ISSN 2321–2705, Volume III, Issue VII, pp.105-110.
  11. S. S. Gaddamwar (2018) "Computational Fluid Dynamic Simulation and Investigational Testing of a Membrane Serpentine Tube Heat Exchanger" Journal of Advanced Research in Dynamical & Control System (JARDCS) Scopus Indexed Journal, Vol. 10, 13-Special Issue, pp.2429-2434
  12. J. S. Khatik, S. V. Yeole, Juned A. R. A. (2014), “Comparative Experimental Study of Simple Absorber Plate with Absorber Plate with Concavities” International Journal of Research in Engineering and Technology, ISSN 2319-1163, Vol-03, pp.13-15.
  13. S. S. Gaddamwar, A. N. Pawar (2018), "Similitude of membrane helical coil with membrane serpentine tube for characteristics of high-pressure syngas: A review" American Institute of Physics (AIP) Conference Proceedings Scopus Indexed Journal, Volume 1966, Issue 1, May 2018.
  14. Dyer J.R.(1975), “The development of Laminar Natural Convective flow in a vertical Uniform Het Flux Duct”, International Journal of Heat & Mass Transfer, Vol.18, Issue-12, 1455-1465.
  15. S. S. Gaddamwar (2019), "An Optimization Of High Pressure And Temperature of Syngas in Underground Coal Mines By Using CFD Analysis of Membrane Serpentine Tube" International Journal of Mechanical and Production Engineering Research and Development (IJMPERD) Scopus Indexed Journal, ISSN(P): 2249-6890; ISSN(E): 2249-8001 Vol. 9, Issue 1, Feb 2019, 617-624.
  16. S.S.Gaddamwar (2018), "Investigational Research of Heat Transmit Distinctiveness of High-Pressure Syngas In Coal Mines Used by Membrane Helical Coil" International Journal of Mechanical Engineering and Technology (IJMET) Scopus Indexed Journal, Volume 9, Issue 1, January 2018, pp. 887–894.
  17. S.S.Gaddamwar (2018), "CFD Analysis of Membrane Helical Coil For Optimization of High Pressure And Temperature of Syngas in Underground Coal Mines" International Journal of Mechanical Engineering and Technology (IJMET) Scopus Indexed Journal, ISSN Print: 0976-6340 and ISSN Online: 0976-6359, Volume 9, Issue 11, November 2018, pp. 1080–1088.
  18. Yasin Varol. (2007). “Buoyancy Induced Heat Transfer and Fluid Flow Inside a Tilted Wavy Solar Collector”, Building and Environment Elsevier Ltd., Vol. 42, Issue 5, pp. 2062-2071.
  19. Sagar S. Gaddamwar, Anand N. Pawar, Pramod A. Naik (2018), Investigational Research of Heat Transmit Distinctiveness of High-Pressure Syngas In Coal Mines Used by Membrane Helical Coil, International Journal of Mechanical Engineering and Technology (IJMET), Volume 9, Issue 1, pp. 887–894

International Journal of Scientific Research in Science, Engineering and Technology

Downloads

Published

2020-04-30

Issue

Volume 7, Issue 2, March-April-2020

Section

Research Articles

License

Copyright (c) IJSRSET

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

[1]
Dr. Rajeshkumar U. Sambhe, Dr. Sagar S. Gaddamwar, " Approximate Representation and Exposition of ISI Flat Plate Collector including Revised Flat Plate Collector : A Review, International Journal of Scientific Research in Science, Engineering and Technology(IJSRSET), Print ISSN : 2395-1990, Online ISSN : 2394-4099, Volume 7, Issue 2, pp.345-350, March-April-2020. Available at doi : https://doi.org/10.32628/IJSRSET207275