Friction Stir Welding of Aluminium Alloy and Stainless Steel and Analysis of Mechanical Properties

Authors

  • Patel Pratikkumar R  Mechanical Department, Gujarat Technological University/Sigma institute of engineering, Vadodara, Gujarat, India
  • Suthar Ghanshyam B  Mechanical Department, Gujarat Technological University/Sigma institute of engineering, Vadodara, Gujarat, India
  • Ray Urvesh J  Mechanical Department, Gujarat Technological University/Sigma institute of engineering, Vadodara, Gujarat, India
  • Shukla Jyotish  Mechanical Department, Gujarat Technological University/Sigma institute of engineering, Vadodara, Gujarat, India
  • Mr. Barot Jaydeep  Assistant Professor, Mechanical Department, Sigma Institute of Engineering, Vadodara, Gujarat, India

Keywords:

Friction, Stir, Welding, Analysis, Properties

Abstract

Friction stir welding is the solid state joining process which can produce high quality welds with either similar or dissimilar materials and has been attracting increasing attention. It is used to join the high strength alloys which are difficult or uneconomical to weld by conventional fusion welding techniques. Friction stir welding was invented and established by The Welding Institute (TWI) in 1991.The aim of this paper is to reviews the work done in the area of joining aluminium alloy and stainless steel, analysis of mechanical properties of weld and concludes by suggesting further scope for research in Friction stir welding and optimum process parameters.

References

  1. A.SureshBabu, C.Devanathan, “An Overview of Friction Stir Welding” IJRMET Vol. 3, Issue 2, May - Oct 2013
  2. J. Qian, J. Li, F. Sun, J. Xiong, F. Zhang, and X. Lin, “An analytical model to optimize rotation speed and travel speed of friction stir welding for defect-free joint,” ScriptaMaterialia, 2012.
  3. A. P. Reynolds, W. Tang, T. G. Herold, and H. Prask, “Structure, properties, and residual stress of 304L stainless steel friction stir welds,” ScriptaMaterialia, vol. 48, no. 9, pp. 1289-1294, 2003.
  4. H. Cho, H. N. Han, S. Hong, J. Park, Y. Kwon, S. Kim, and R. J. Steel, “Microstructural analysis of friction stir welded ferritic stainless steel,” Materials Science and Engineering: A, vol. 528, no. 6, pp. 2889-2894, 2011.
  5. K. V. Jata, and S. L Semiatin, “Continuous dynamic recrystallization during friction stir welding of high strength aluminum alloys,” ScriptaMaterialia, vol. 43, no. 8, pp. 743-749, 2000.
  6. B. Heinz and B. Skrotzki, “Characterization of a friction-stir-welded aluminum alloy 6013,” Metallurgical and Materials Transactions B, vol. 33, no. 3, 2002, pp. 489-498.
  7. Y. S. Sato, T. W. Nelson, and C. J. Sterling, “Recrystallization in type 304L stainless steel during friction stirring,” ActaMaterialia, vol. 53, no. 3, pp. 637-645, 2005
  8. Manish P. Meshram, Basanth Kumar Kodli, Suhash R. Dey, “Friction Stir Welding of Austenitic Stainless Steel by PCBN Tool and Its Joint Analyses, Procedia Materials Science 6 (2014) 135 – 139
  9. C. Meran, O.E. Canyurt, “Friction Stir Welding of austenitic stainless steels” JMMEEvolume 43 November 2014.
  10. Joaquín M. Piccinia,b, Hernán G. Svobodab, “Effect of the tool penetration depth in Friction Stir Spot Welding (FSSW) of dissimilar aluminum alloys” Procedia Materials Science 9 ( 2015 ) 504 – 513
  11. H. Schmidt, J. Hattel, and J. Wert, “An analytical model for the heat generation in friction stir welding,” Model. Simul. Mater. Sci. Eng., vol. 12, pp. 143–157, 2004.
  12. M. Assidi, L. Fourment, S. Guerdoux, and T. Nelson, “Friction model for friction stir welding process simulation: Calibrations from welding experiments,” International Journal of Machine Tools and Manufacture, vol. 50, no. 2, pp. 143-155, 2010.
  13. H. B. Schmidt, and J. H. Hattel, “Thermal modeling of friction stir welding,” ScriptaMaterialia, vol. 58, no. 5, pp. 332-337, 2008.
  14. W. S. Lee, J. I. Cheng, and C. F. Lin, “Deformation and failure response of 304L stainless steel SMAW joint under dynamic shear loading,” Mater Sc.Eng. A, vol. 381, no. 1–2, pp. 206–15, 2004.
  15. R. Nandan, T. DebRoy, and H. K. D. H. Bhadeshia, “Recent advances in friction-stir welding–process, weldment structure and properties,” Progress in Materials Science, vol. 53, no. 6, pp. 980-1023, 2008 .
  16. R. S. Mishra and Z. Y. Ma, “Friction stir welding and processing,” Materials Science and Engineering: R: Reports, vol. 50, no. 1–2, pp. 1-78, 2005.
  17. T. J. Lienert, W. Stellwag, and L. R. Lehman. Comparison of heat inputs: Friction stir welding vs. arc welding. [Online] available:http://174.122.108.74/confrences/abstracts/2002/011.pdf
  18. Maulikkumarpatel,dipteshkumarpatel, jeetendrakumarvadher, “effect of process parameter on AL6061 T6 using friction stir welding by RSM method”.
  19. Jeomkee Paik, “Mechanical properties of friction stir welded aluminium alloys 5083 and 5383”.
  20. S Ravikumar, V seshagiri and R V Pranesh, “Effect of process parameters on mechanical properties of friction stir welded dissimilar materials between AA6061 T651 and AA7075 T651 alloys”.International Journal of Advanced Mechanical Engineering. ISSN 2250-3234 Volume 4, Number 1 (2014), pp. 101-114
  21. V.C. Sinha, S kundu, S Chatterjee, “Microstructure and mechanical properties of similar and dissimilar joints of aluminium alloy and pure copper by friction stir welding”.
  22. Sudhirkumar and Pradeepkumar, “Study the effect of parameters of friction stir welding on the impact strength of aluminium 6063”.
  23. N. T. Kumbha and K. Bhanumurthy,“Friction StirWelding of Al 5052 with Al 6061 Alloys” Hindawi Publishing Corporation Journal of Metallurgy Volume 2012, Article ID 303756
  24. A soltani, M shakeri, S nourouzi, H jamshidi, “Effect of friction stir welding parameters on mechanical properties of aluminium alloy to austenitic stainless steel lap joint”.
  25. C. Meran, O.E. Canyurt,“Friction Stir Welding of austenitic stainless steels”JAMME vol. 43 November 2014

International Journal of Scientific Research in Science, Engineering and Technology

Downloads

Published

2018-04-10

Issue

Volume 4, Issue 5, March-April-2018

Section

Research Articles

License

Copyright (c) IJSRSET

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

[1]
Patel Pratikkumar R, Suthar Ghanshyam B, Ray Urvesh J, Shukla Jyotish, Mr. Barot Jaydeep, " Friction Stir Welding of Aluminium Alloy and Stainless Steel and Analysis of Mechanical Properties, International Journal of Scientific Research in Science, Engineering and Technology(IJSRSET), Print ISSN : 2395-1990, Online ISSN : 2394-4099, Volume 4, Issue 5, pp.567-573, March-April-2018.