Investigation of the Effect of Fused Deposition Process Parameter on Compressive Strength and Roughness Properties of Abs-M30 Material

Authors

  • Gaurav Shah  Department Mechanical Engineering, Babaria Institute of Technology Vadodara, Gujarat, India
  • Arpan Shah  Department Mechanical Engineering, Babaria Institute of Technology Vadodara, Gujarat, India

Keywords:

FDM, Taghuchi method, built up time

Abstract

The process parameters of FDM manufacturing technology is very important for obtaining high quality parts, good mechanical properties. Several optimization techniques used such as Response surface methodology, Taguchi method, FF, ANN etc. much research work has been carried out in ABS, PC, PPSF, Nylon-12, PC-ABS blend for optimizing process parameters to identify improved surface roughness, mechanical properties and built-up time.

References

    1. Ahn Sung Hoon, Montero Michael, Odell Dan, Roundy Shad, Wright Paul K. (2002). Anisotropic material properties of fused deposition modelling ABS, Rapid prototyping journal, 8 (4): 248-257 .
    1. Omar A. Mohamed, Syed H. Masood, Jahar L. Bhowmik, Optimization of fused deposition modeling process parameters: a review of current research and future prospects .
    2. Mohammad Shojib Hossain, Jorge Ramos, David Espalin, Improving Tensile Mechanical Properties of FDM-Manufactured Specimens via Modifying Build Parameters.
    3. Constance Ziemian , Improving Tensile Mechanical Properties of FDM-Manufactured Specimens via Modifying Build Parameters.
    4. Dr. K. G. Dave , An Experimental Investigation of Effect of Process Parameters on Surface Roughness of Fused Deposition Modeling Built Parts.
    5. S.Dinesh Kumar,  Parameter Optimization of ABS-M30i Parts Produced by Fused Deposition Modeling for Minimum Surface Roughness.
    6. M Alhubail, Taguchi-based Optimisation of Process Parameters of Fused Deposition Modelling for Improved Part Quality.
    7. Investigation on the effect of Fused Deposition Modeling Process Parameters on Flexural Surface Roughness properties of PC-ABS blend.  S. Manikandan, V. Prabhu Raja.
    8. Parametric Optimization of Fused Deposition Modeling Process in Rapid Prototyping Technology in ABS-M30 Mr. Vishal N. Patel, Mr. Kamlesh P. Kadia.
    9. Experimental investigation and empirical modelling of FDM process for compressive strength improvement in ABS-400 materials.A.K. Sood ,R.K. Ohdar, S.S.Mahapat.

    Web Site

    • http://www.worldscibooks.com/engineering/6665.html
    • http://en.m.wikipedia.org/wiki/fused_deposition_modeling
    • http://en.m.wikipedia.org/wiki/Taguchi_method

    Books 

    • Pulak M.pandey "Rapid Prototyping Technologies, Application and Part Deposition planning" Department of mechanical engineering Indian institute of technology Delhi.(2009)
    • "CAD-CAM & Rapid prototyping application evaluation" reverse engineering & rapid prototyping  download free eBooks at bookboon.com
    • "Meet Minitab 17", A Minitab 17 software guide
    • H.Theil, Principles of Econometrics 622-27(1971); G.Chow, Econometrics 320-47(1983)
    • Techniques for the estimation of non linear regression have been developed. See, e.g G.Chow, supra note 9, at 220-51
    • R.K. Roy "A primer on Taguchi method", Van Nostrand Reinhold, Newyork U.S.A. p.p. 101 -103.

International Journal of Scientific Research in Science, Engineering and Technology

Downloads

Published

2017-12-31

Issue

Volume 2, Issue 2, March-April-2016

Section

Research Articles

License

Copyright (c) IJSRSET

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

[1]
Gaurav Shah, Arpan Shah, " Investigation of the Effect of Fused Deposition Process Parameter on Compressive Strength and Roughness Properties of Abs-M30 Material, International Journal of Scientific Research in Science, Engineering and Technology(IJSRSET), Print ISSN : 2395-1990, Online ISSN : 2394-4099, Volume 2, Issue 2, pp.1289-1296, March-April-2016.