A Review : Design And Analysis of Welding Fixture for the Rack and Pinion Assembly

Authors

  • N. B. Pawar  Student of M. E. Department of Mechanical Engineering Shri Gulabrao Deokar College of Engineering, Jalgaon, Maharashtra, India
  • Prof. P. P. Patil  Assistant Professor, Department of Mechanical Engineering, Shri Gulabrao Deokar College of Engineering, Jalgaon, Maharashtra, India
  • Prof. R. Y. Patil  H.O.D. Department of Mechanical Engineering, Shri Gulabrao Deokar College of Engineering, Jalgaon, Maharashtra, India.

Keywords:

Design, Analysis, Welding Fixture, assembly of Cross member Rear Lower Wishbone component

Abstract

In most of manufacturing industry used for assembly of component for used the welding fixture. The fixtures are the important part of the welding as fixtures are used in manufacturing of different products during welding to hold the different parts of that respective product. Fixture having direct impact for the productivity and quality of product. welding fixture are design for the component which have difficult to weld. In normal way welding of different parts of component not possible for without holding device. The welding fixture are important holding device. The number of parts to be welded in proper position in fixture and tightened. When the fixture are holding work piece for produced by the welding stress. The proposes a design and analysis approach in fixture of sheet metal assemblies for Cross member Rear Lower Wishbone component. The design of an assembly fixture for a particular tail cone has been completed convenient to the existing locating principles. The design of welding fixture and component using for Pro-E and CAD software. using the Finite Element Analysis (FEA) by using ANSYS software that provides best output within few seconds

References

  1. Jigar D Suthar, K.M Patel, Sanjay G Luhana “Design and analysis of fixture for welding an exhaust impeller”International journal of Engineering ScienceDirect and Technology , vol. 51 ( 2013 ) 514 – 519
  2. Naveen A M, V A Girisha, Pruthvi H M “Design And Analysis Of Welding Fixture For Motor Case Assembly” On IJMPE, ISSN: 2320-2092, Volume- 2, Issue-8, Aug.-2014
  3. Kalpesh Khetani, Jafar Shah, Vishal Patel  “ Design and Thermal Stress Analysis of Welding Fixture of a Brake Pedal” IJRMEE  ISSN: 2349-7947 Volume: 2 Issue: 5 029 – 032,May-2015.
  4. Chetan D. Borse, Prasad V. Thete, Ravi P. Vishwakarma, Jainendrakumar S. Yadav “ Design And Analysis Of Fixture For A Stone Crusher Body” On IJRET eISSN: 2319-1163 | pISSN: 2321-7308, Volume: 04 Issue: 06 | June-2015.
  5. M. Mhaske, R. M. Metkar, S. D. Hiwase “Design and Analysis of Welding Fixture for Tacking and Welding of Inner Boom of Loadall Handler” On IJRMET, ISSN : 2249-5762, Vol. 5, Issue 2 ,May - Oct 2015
  6. Omkar Joshi, Dr. Arunkumar “ Design And Analysis Of Welding Fixture For Orbital Welding Machine”On IJPME,   Volume III Issue IV October – December 2015
  7. Vaishak bhandary M, Sudeep N S, Naveenakrishna P V “Design and Analysis of Robot Full Welding Fixture for Front Chassis of Wheel Loader” NCAMES ,ISSN: 2231-5381- 2016
  8. C. A. Kubade , Dr. S.V. Patil , Mr. V. P. Patil “Design and Analysis of Welding Fixture for Automotive Component using FEA” IJARIIE-ISSN(O)-2395-4396, Vol-2 Issue-4 2016

International Journal of Scientific Research in Science, Engineering and Technology

Downloads

Published

2017-02-28

Issue

Volume 3, Issue 1, January-February-2017

Section

Research Articles

License

Copyright (c) IJSRSET

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

[1]
N. B. Pawar, Prof. P. P. Patil, Prof. R. Y. Patil "A Review : Design And Analysis of Welding Fixture for the Rack and Pinion Assembly" International Journal of Scientific Research in Science, Engineering and Technology (IJSRSET), Print ISSN : 2395-1990, Online ISSN : 2394-4099, Volume 3, Issue 1, pp.30-33, January-February-2017.