Evaluation of Mechanical Properties of Micro-Titanium and CNT Reinforced Copper Based MMC

Authors

  • Dr. Ranjith V  Assistant Professor, Mechanical Engineering, Dr. Ambedkar Institute of Technology, Bangalore, Karnataka, India
  • Dr. H K Shivanand2  Professor, Mechanical Engineering, Bangalore University/UVCE/Company, Bangalore, Karnataka, India
  • Dr. Tukaram Jadhav3  Guest Faculty, Mechanical Engineering, Bangalore University/UVCE/Company, Bangalore, Karnataka, India
  • Verma R4  Ph.D Scholar Mechanical Engineering, Bangalore University/UVCE/Company, Bangalore, Karnataka, India
  • Puneeth P  PG Scholar, Mechanical Engineering, Bangalore University/UVCE/Company, Bangalore, Karnataka, India

DOI:

https://doi.org//10.32628/IJSRSET218315

Keywords:

Micro-Titanium, CNT, Tensile strength, Compression strength, Hardness and Technology

Abstract

Copper based composites plays a vital role in the field of marine, aerospace, automobile and power sector for making of components like electrical sliding contacts, gears, bearings, bushes, brakes and clutches etc. Even though promising reinforcements are available for the composites, always researchers search for the new combination of matrix and reinforcement for tailored properties and cost effectiveness. CNT is one of the effective reinforcement used in the metal matrix composites by various researches because of its excellent properties. The present work is focused on the preparation of copper/CNTs/Micro-Titanium composite through stir casting technique performance studies of the composite are made on the mechanical properties. The composite prepared with reinforcement such as CNTs and Micro-Titanium of 0.5, 1, 1.5 % and 1, 3 & 5wt. % were studied. The Tensile strength, Compression strength, Hardness was found out via experimentation.

References

  1. Hermann Holzer, David C. Dunand, Phase transformation and thermal expansion of Cu/ZrW2O8 metal matrix composites, Journal of materials research, 14 (1999) 780-789.
  2. Prof.S.A, Deshmukh, Dhavale Priyanka S, Kokate Priyanka M, Mechanical Properties of Sintered CuZn30 (Brass) - MWCNT Composite Fabricated By Powder Metallurgy. International Journal of Current Trends in Science and Technology, 8(2001) 103-115.
  3. S.F Moustafa, Z Abdel-Hamid, A.M Abd-Elhay, Copper matrix SiC and Al2O3 particulate composites by powder metallurgy technique, Materials Letters, 53 (2002) 244-249.
  4. J.P Tu, N.Y Wang, Y.Z Yang, W.X Qi, F Liu, X.B Zhang, H.M Lu, M.S Liu, Preparation and properties of TiB2 nanoparticle reinforced copper matrix composites by in situ processing, Materials Letters,52(2002)448-452.
  5. H.Kato,M.Takama,Y.Iwai,K.Washida,Y.Sasaki, Wear and mechanical properties of sintered copper-tin composites containing graphite or molybdenum disulfide, Wear, 225 (2003) 573-578.
  6. Kuen-Ming Shu, G.C Tu, The microstructure and the thermal expansion characteristics of Cu/SiCp composite, Materials Science and Engineering: A, 349(2003)236-247.
  7. Y.Zhan, G.Zhang, Friction and Wear Behavior of Copper Matrix Composites Reinforced with SiC and Graphite Particles, Tribology Letters, 17 (2004) 91-98.
  8. Th. Schubert, B. Trindade, T. Weibgarber, B. Keiback, Interfacial design of Cu-based composites prepared by powder metallurgy for heat sink applications, Material Science and Engineering A, 475 (2008) 39-44.
  9. Zuhailawati Hussain, Radzali Othman, Bui Duc Long, Minoru Umemoto, Synthesis of copper-niobium carbide composite powder by in situ processing, Journal of Alloys and Compounds, 464(2008)185-189.
  10. F. Shehata, A. Fathy, M. Abdelhameed, S.F. Moustafa, Preparation and properties of Al2O3 nanoparticle reinforced copper matrix composites by in situ processing, Materials&Design,30(2009)2756-2762.
  11. Mohsen Barmouz, Mohammad Kazem Besharati Givi, Fabrication of in situ Cu/SiC composites using multi-pass friction stir processing: Evaluation of microstructural, porosity, mechanical and electrical behavior, Composites Part A: Applied Science and Manufacturing, 42 (2011)1445-1453.
  12. P.Yao, Y.xiao, J.Deng, Study on Space Copper-Based Powder Metallurgy Friction Material and its Tribological Properties, Material Science &Engineering, 284-286 (2011) 479-487.
  13. M.Ramachandra, A. Abhishekb, P. Siddeshwarc, V. Bharathid, Hardness and Wear Resistance of ZrO2 Nano Particle Reinforced Al Nanocomposites Produced by Powder Metallurgy, Procedia Materials Science, 10 ( 2015 ) 212 - 219
  14. K. Soorya Prakash, P.M. Gopala, D. Anburoseb, V. Kaviman, Mechanical, corrosion and wear characteristics of powder metallurgy processed Ti-6Al-4V/B4C metal matrix composites, Ain Shams Engineering Journal, (2016)
  15. TielongHan,JiajunLi,NaiqinZhao,ChunshengShi,EnzuoLiu,FangHe,LiyingMa,QunyingLi,ChunnianHe,Insitu fabrication of nano-sized TiO2 reinforced Cu matrix composites with well-balanced mechanical properties and electrical conductivity, Powder Technology 321(2017)66-73
  16. Nalin Somania, Naman Sharma, Aayushi Sharma, Yash Kumar Gautam, Paras Khatri, J.Allanson Agnal Solomon, Fabrication of Cu-SiC Composites using Powder Metallurgy Technique, Materials Today: Proceedings 020017
  17. Jun-hui Nie, Cheng-chang Jia, Xian Jia, Yi Li, Ya-feng Zhang, and Xue-bing Liang,Fabrication and thermal conductivity of copper matrix composites reinforced by tungsten-coated carbon nanotubes, International Journal of Minerals, Metallurgy and Materials Volume 19, Number 5, May 2012, pp440- 446
  18. B.T., Than, Tran, X.T., Nguyen, Bui, H.T., V.C., Doan, D.P. and Phan, N.M. (2011). The Effect of Sintering Temperature on the Mechanical Properties of a Cu/CNT Nanocomposite Prepared via a Powder Metallurgy Method, Advances in Natural Science Nanoscience and Nanotechnology.
  19. Barzegar, M. and Ataie, A. (2014). Role of Intensive Milling on Microstructure and Physical Properties of Cu80Fe20/10CNT Nanocomposite, Journal of Ultrafine Grained and Nanostructured Material, 47: 37-42
  20. Bakhshaei, P., Ataie, A., and Abdizadeh, H. (2013). Effect of CNT Addition on the Characteristics of Cu-Ni/CNT Nanocomposite, Jounal of Nanostructures, 3: 403-409.
  21. Pham, V.M., Bui, H.T., Tran, B.T., Than, X.T., Nguyen, V.C., Doan, D.P. and Phan, N.M. (2011). The Effect of Sintering Temperature on the Mechanical Properties of a Cu/CNT Nanocomposite Prepared via a Powder Metallurgy Method, Advances in Natural Science Nanoscience and Nanotechnology, 2: 4.
  22. Guiderdoni, Ch., Pavlenko, E., Turq, V., Weibel, A., Puech, P., Estournes, C., Peihney, A., Bacsa, W. and Laurent, Ch. (2013). The Preparation of Carbon Nanotubes (CNT)/Copper Composites and the Effect of the Number of CNT Walls on their Hardness Friction and Wear Properties, Carbon, 58: 185-197.
  23. Hongqi, l., Amit, M., Zenji, H., Carl, C. K., Nathan, A. M., Patricia, O. D. and Yuntian, Z. (2009). Strong and Ductile Nanostructured Cu- Carbon Nanotube Composite, Applied Physics Letter, 95: 071907.
  24. Dong, S.R., Pj, P.J., and Zhang, X.B. (2001). An Investigation of the Sliding Wear Behavior of Cu-matrix Composite Reinforced by Carbon nanotubes, Materials Science and Engineering, A131: 83-87
  25. Chu, K., Qingying, W., Chengchang, L., Xuebing, L., Junhui, N., Wenhuai, T., Guosheng, G. and Hong, G. (2010). Fabrication and effective thermal conductivity of multi-walled carbon nanotubes reinforced Cu matrix composites for heat sink applications, Composites Science and Technology, 70: 298- 304.
  26. Kim, T., Seung, C., Seong, H.H. and Soon, H.H. (2006). Microstructures and Tensile Behavior of Carbon Nanotube Reinforced Cu Matrix Nanocomposites, Materials Science and Engineering, A430: 27-33
  27. Kim, K.T., Ecket, J., Liu, G., Jin, M.P., Byung, K.L. and Soon, H.H. (2011). Influence of Embedded-Carbon Nanotubes on the Themal Properties of Copper Matirix Nanocomposite Processed by Molecular-Level Mixing, Scipta Materialia, 64: 181-184
  28. Dong, H., Seung, I., Byung, y., Hoon, M., Do, S. and Soon, H. (2012). Synergistic Strengthening by Load Transfer Mechanism andGrain Refinement of CNT/Al-Cu Composites, Carbon, 50: 2417-2423.
  29. Seung, I., Cha., Kyung, T., Kim., Salman, N.A., Chan, B.M. and Soon, H.H. (2005). Extraordinary Strengthening Effect of Carbon Nanotubes in Metal-Matix Nanocomposite Pocessed by Molecula-Level Mixing Advanced Mateial, 17: 1377-1381.
  30. Nor Shamimi Shaari, Jamaliah Md Said, Aidah Jumahat, Muhammad Hussain Ismail, Vol. 69 Issue: 3, Industrial Lubrication and Tribology,Wear behaviour of copper/carbon nanotubes pp.342-347,
  31. Tu, J.P., Yang, Y.Z., Wang, L.Y., Ma, X.C. and Zhang, X.B. (2001), “Tribological properties of carbon-nanotube-reinforced copper composites”, Tribology Letters, Vol. 10 No. 4, pp. 225-228.
  32. Rajkumar, K. and Aravindan, S. (2011), “Tribological studies on microwave sintered copper-carbon nanotube composites”, Wear, Vol. 270 Nos 9/10, pp. 613-621.
  33. R. Vignesh Babu and S. Kanagaraj Thermal, electrical and mechanical characterization of microwave sintered Copper/Carbon nanotubes (CNT) composites against sintering duration, CNT diameter and its concentration ,Journal of Materials Processing Technology,Vol 1,2018,pp-532-538.
  34. Yang, Huijun, Luo, Ruiying, Han, Suyi, Li, Midan, Effect of the ratio of graphite/pitch coke on the Mechanical and tribological properties of copper-carbon composites, Wear 268 (2010) 1337-1341.
  35. Silvain, J.F., Petitcorps, Y. Le, Sellier, E., Bonniau, P. and Heim, V., Elastic moduli, thermal expansion and Microstructure of copper-matrix composite reinforced by continuous graphite fibres, Composites, 25, 7(1994) 570-574.
  36. Ma, Wenlin, Jinjun, Lu, Effect of surface texture on transfer layer formation and tribological behaviour of copper-graphite composite, Wear 270(2011) 218-229.
  37. Zhao, Heijun, Liu, Lei, Wu, Yating, Hu, Wenbin, Investigation on wear and corrosion behaviour of Cu- graphite composites prepared by electroforming, Composites Science and Technology 67 (2007) 1210- 1217.
  38. Dorfman, Simon, Fuks, David, Stability of copper segregations on copper/carbon metal matrix Composite interfaces under alloying, Composites Science and Technology 57 (1997) 1065-1069.
  39. Dash, K., Ray, B.C., Chaira, D., Synthesis and characterization of copper-alumina metal matrix Composite by conventional and spark plasma sintering, Journal of Alloys and Compounds 516 (2012) 7884.
  40. M. Abdelhameed, F. Shehata, A. Fathy,,Moustafa, J. Alloys Compd. 476 (2008) 300-305. Friction and wear of copper- graphite Composites made with Cu-coated and uncoated graphite powder, Wear 253 (2002) 699-710.
  41. Kovacik, J., Emmer, Stefan, Bielek, J., Kelesi, Lubom?r, Effect of composition on friction coefficient of Cu-graphite composites. Wear 265 (2008) 417-421.
  42. Riccardo Casati and Maurizio Vedani; “Metal Matrix Composites Reinforced by Nano -Particles”, Journal of Metals (2014), Vol. 4, pp. 65-83.
  43. H. Sun Ph.D., J. E. Orth Ph.D., H. G. Wheat Ph.D.; “ Corrosion Behavior of Copper based Metal Matrix Composite”, Journal of JOM; Volume 45, Issue 9, pp 36-41.
  44. Shubham Mathur, Alok Barnawal; “Effect of Process Parameter of Stir Casting on Metal Matrix Composites”; International Journal of Science and Research (IJSR) (2013), 395-398. 19-
  45. Shikhar Gupta And Himanshu Bhartia Review On Copper-Graphite Composite Material Fabrication & Its Mechanical Properties. Vol-2 Issue-5 2016 Ijariie-Issn(O)-2395-4396
  46. Wang X, Li J, Wang Y (2016) Improved high temperature strength of copper-graphene composite material. Mater Lett 181:309-312.
  47. Chu K, Wang XH, Li YB, Huang DJ, Geng ZR, Zhao XL, Liu H, Zhang H (2018) Thermal properties of graphene/ metal composites with aligned graphene. Mater Des 140:85-94
  48. Si X, Li M, Chen F, Eklund P, Xue J, Huang F, Du S, Huang Q (2017) Effect of carbide interlayers on the microstructure and properties of graphene-nanoplatelet-reinforced copper matrix composites. Mater Sci Eng A 708:311-318
  49. Mai YJ, Zhou MP, Ling HJ, Chen FX, Lian WQ, Jie XH (2018) Surfactant-free electrodeposition of reduced graphene oxide/copper composite coatings with enhanced wear resistance. Appl Surf Sci 433:232-239
  50. Kim KT, Eckert J, Liu G, Park JM, Lim BK, Hong SH. 2011 Influence of embedded-carbon nanotubes on the thermal properties of copper matrix nanocomposites processed by molecular level mixing. Scr. Mater. 64, 181-184.
  51. Adnan Maqbool, F Ahmad Khalid, M Asif Hussain and Nabi Bakhsh Synthesis of copper coated carbon nanotubes for aluminium matrix composites Materials Science and Engineering,2014.
  52. S. Nallusamy, M. Rajaram Narayanan, J. Logeshwaran,Synthesis and Machining Characterization of Copper-Multiwalled Carbon Nanotubes-Graphene Hybrid Composite Using SEM and ANOVA Journal of Nano Research Submitted: 2017-07-17 ISSN: 1661-9897, Vol. 50, pp 105-115
  53. Hemant Nautiyal , Prabhat Srivastava,OmPrakash Khatri, Sunil Mohan and Rajnesh Tyagi Wear and friction behaviour of copper based nano hybrid composites fabricated by spark plasma sintering Mater. Res. Express 6 (2019) 0850h
  54. D. Nayakab, N. Rayab, R. Sahoob & M. Debataab Analysis of Tribological Performance of Cu Hybrid Composites Reinforced with Graphite and TiC Using Factorial Techniques Tribology Transactions, 57: 908-918, 2014
  55. Kaczmar, J. W., Pietrzak, K., and W?osin´ ski, W. (2000), “The Production and Application of Metal Matrix Composite Materials,” Journal of Materials Processing Technology, 106(1-3), pp 58-67.
  56. Roy, M., Venkataraman, B., Bhanuprasad, V. V., Mahajan, Y. R., and Sundararajan, G. (1992), “The Effect of Participate Reinforcement on the Sliding Wear Behavior of Aluminum Matrix Composites,” Metallurgical Transactions A, 23(10), pp 2833-2847.
  57.  Tjong, S. C. and Lau, K. C. (2000), “Tribological Behaviour of SiC Particle- Reinforced Copper Matrix Composites,” Materials Letters, 43(5-6), pp 274-280.
  58. Onat, A. (2010), “Mechanical and Dry Sliding Wear Properties of Silicon Carbide Particulate Reinforced Aluminium-Copper Alloy Matrix Composites Produced by Direct Squeeze Casting Method,” Journal of Alloys and Compounds, 489(1), pp 119-124.
  59. Dhokey, N. B. and Paretkar, R. K. (2008), “Study of Wear Mechanisms in Copper-Based SiCp (20% by Volume) Reinforced Composite,” Wear, 265(1-2), pp 117-133
  60. Zhan, Y. and Zhang, G. (2006), “The Role of Graphite Particles in the High-Temperature Wear of Copper Hybrid Composites against Steel,” Materials & Design, 27(1), pp 79-84.
  61. A.I.Rudskoy, A.G.Nasibulin, T.S.Koltsova, O.V.Tolochko Novel Metal Matrix/Carbon Composites Forairspace Applications 29th Congress Of The International Council Of The Aeronautical Sciences.2014,Pp-7-12
  62. Ke Chu ,Hong Guo Chengchang, Jia Fazhang Yin, Ximin Zhang, Xuebing Liang Hui Chen Thermal Properties of Carbon Nanotube-Copper Composites for Thermal Management Applications, Nanoscale Res Lett (2010) 5:868-874
  63. T. Babul, M. Baranowski, N. Sobczak, M. Homa, and W. Les´ niewskiThermophysical Properties of Cu-Matrix Composites Manufactured Using Cu Powder Coated with GrapheneJournal of Materials Engineering and Performance2015, 4, p 2282-2291
  64. Lim, B., C.-J. Kim, B. Kim, U. Shim, O. Seyoung, B.-H. Sung, J.-H. Choi, and S. Baik. 2006. “The Effects of Interfacial Bonding on Mechanical Properties of Single- Walled Carbon Nanotube Reinforced Copper Matrix
  65. Koppad, P. G., K. T. Kashyap, V. Shrathinth, T. A. Shetty, and R. G. Koppad. 2013. “Microstructure and Microhardness of Carbon Nanotube Reinforced Copper Nanocomposites.” Journal Materials Science and Technology 29 (5): 605-609.
  66. Kakac, S., and A. Pramuanjaroenkij. 2009. “Review of Convective Heat Transfer Enhancement with Nanofluids.” International Journal of Heat and Mass Transfer 52: 3187- 3196.
  67. S. Prabhu, R. Ambigai & B.K. Vinayagamthermal And Surface Analysis Of Copper-Cnt And Copper-Graphene-Based Composite Using Taguchi-Grey Relational Analysisaustralian Journal Of Mechanical Engineering,2018
  68. J.P. Tu , N.Y. Wang, Y.Z. Yang, W.X. Qi, F. Liu , X.B. Zhang , H.M. Lu b, M.S. Liu a Preparation and properties of TiB nanoparticle reinforced copper 2 matrix composites by in situ processing, Materials Letters 52 Ž2002. 448-452
  69. Siddabathula Madhusudan a,Mohammed Moulana Mohiuddin Sarcar b, Narsipalli Bhargava Rama Mohan Rao., Mechanical properties of Aluminium-Copper(p) composite metallic materials., Journal of Applied Research and Technology 293-299,Vol 14, 2016
  70. Shaaz abulais, vikrant yadav, aniruddha muley., fabrication and characterization of copper matrix hybrid composite., International Journal of Mechanical And Production Engineering, ISSN: 2320-2092
  71. Velugula Mani Kumar and Chinta Neelima Devi., Evaluation of mechanical characteristics for Aluminium-copper Metal matrix composite., Research Journal of Engineering Sciences Vol. 3(3), 1-5, March (2014)
  72. P S Kori , Mohan Vanarotti , B M.Angadi , V V Nagathan, V Auradi , M I Sakri., Effect of Copper Coated SiC Reinforcements on Microstructure, Mechanical Properties and Wear of Aluminium Composites., IOP Conf. Series: Materials Science and Engineering 225, 2017
  73. Harshpreet Singh, Lailesh Kumar, Syed Nasimul Alam., Development of Cu Reinforced SiC Particulate Composites., IOP Conf. Ser.: Mater. Sci. Eng. 75 012007
  74. Manvandra Kumar Singh, Mechanical property of dual reinforced copper based hybrid composite., Conference: National Conference on Product Design and Manufacturing (NCPDM-2015), At Mechanical Engineering Department Motilal Nehru National Institute of Technology Allahabad.
  75. R. Noor Ahmed and C. S. Ramesh., tribological properties of cast copper-SiC-graphite hybrid composites, International Symposium of Research Students on Materials Science and Engineering December 20-22, 2004,
  76. RAM PRABHU., Processing and study of the wear and friction behaviour of discrete graded Cu hybrid composites, Bull. Mater. Sci., Vol. 38, No. 3, pp. 753- 760, June 2015
  77. Mohsen Barmouz Vahid Zal., Hamed Pashazadeh., Mechanical and Microstructural Characterization of Hybrid Cu-SiC-Zn Composites Fabricated Via Friction Stir Processing., Mat. Res. vol.19 no.6 São Carlos Nov./Dec. 2016
  78. R. K. Khatitrkar, s. G. Sapate., abrasive wear behaviour of copper-SiC and copper-sio2 composites., International Journal of Modern PhySiCs: Conference Series Vol. 22 (416-423), 2013
  79. H. M. Mallikarjuna , C. S. Ramesh , Praveennath G. Koppad , K. T. Kashyap , R. Keshavamurthy., Microstructure and Microhardness of Carbon Nanotube-Silicon Carbide/Copper Hybrid Nanocomposite Developed by Powder Metallurgy., Indian Journal of Science and Technology, Vol 9(14), DOI: 10.17485/ijst/2016/v9i14/84063, April 2016
  80. Chandramouli Subramaniam, Yuzuri Yasuda, Satoshi Takeya,b Seisuke Ata,ac Ayumi Nishizawa,a Don Futaba,ac Takeo Yamadaac and Kenji Hata Carbon nanotube-copper exhibiting metal-like thermal conductivity and silicon-like thermal expansion for efficient cooling of electronics, Nanoscale, 2014, 6, 2669-267
  81. Sachin S Raj, Elavarasan E, Arundeva. S, Devaraj. S, Gokulraj. Govindharasu Tribological Test on Copper based Hybrid Composite Material International Journal of Engineering Research & Technology (IJERT) Volume 6, Issue 10
  82. Mr. A. R. Dhatrak Dr. K. B. Kale Wear Rate Investigation of Aluminium Based Silicon Carbide Metal Matrix Composite Embedded with Copper IJIRST -International Journal for Innovative Research in Science & Technology|,Volume 3, Issue 04 September 2016,376-384.
  83. Yongzhong Zhan and Guoding Zhang Friction and wear behavior of copper matrix composites reinforced with SiC and graphite particles Tribology Letters, Vol. 17, No. 1, July 2004 91-98
  84. Yang, Huijun, Luo, Ruiying, Han, Suyi, C G Kang et al. Li, Midan, Effect of the ratio graphite/pitch coke on the Mechanical and tribological properties of copper- carbon composites, Wear 268 (2010) 1337-1341.
  85. Ma, Wenlin, Jinjun, Lu, Effect of surface texture on transfer layer formation and tribological behaviour of copper-graphite composite, Wear 270(2011) 218-229.
  86. Zhao, Heijun, Liu, Lei, Wu, Yating, Hu, Wenbin, Investigation on wear and corrosion behavior of Cu- graphite composites prepared by electroforming, Composites Science and Technology 67 (2007) 1210- 1217.
  87. David, Fuks , Simon, Stability of copper segregations on copper/carbon metal matrix Composite interfaces under alloying, Composites Science and Technology 57 (1997) 1065-1069
  88. Emmer, Stefan, Bielek, J., Kelesi, Lubom?r, Effect of composition on friction coefficient of Cu-graphite composites. Wear 265 (2008) 417-421.
  89. G. G. Sozhamannan, S. Balasivanandha Prabu, V. S. K. Venkatagalapathy; “Effect of Processing Paramters on Metal Matrix Composites: Stir Casting Process”; Journal of Surface Engineered Materials and Advanced Technology by SCIRP (2012) 2, 11-15
  90. P. Yih, D. D. L. Chung; “Titanium Diboride Copper Matrix Composite”; Journal of Materials Science (1997); Volume 32, Issue 7 , pp 1703-1709.
  91. Shenbaga Vinayaga Moorthi, S.C. ettivel, N. Selvakumar ; “Process development in stir casting and investigation on microstructures and wear behavior of TiB2 on Al6061 MMC”; Materials and Design 59 by elsevier (2014), 383-396.
  92. Shubham Mathur, Alok Barnawal; “Effect of Process Parameter of Stir Casting on Metal Matrix Composites”; International Journal of Science and Research (IJSR) (2013), 395-398. |
  93. Nur Hawadah, Mohd Subhi, Zuhailawati, Hussain Radzali, Othman; “Fabrication of titanium carbide reinforced copper matrix composite by in-situ processing”. Publisher: Universiti Malaysia Perlis (2010), pp. 74-81.
  94. Yongzhong Zhan, Guoding Zhang; “Friction and Wear Behavior of Copper Matrix Composites reinforced with SiC and Graphite Particles”, Journal of Tribology Letters (2004), Volume 17, Issue 1 , pp 91-98.
  95. S. Naher, D. Brabazon, L. Looney ; “Simulation of the stir casting process”, Journal of Materials Processing Technology by ELSEVIER, 143-144 (2003) 567-571.
  96. K. Sekar, Allesu K. and M.A. Joseph; “Design of a stir casting machine”, American International Journal of Research in Science, Technology, Engineering & Mathematics (2013), pp. 56-62.
  97. R.Noor Ahmed And C.S.Ramesh Tribological Properties Of Cast Copper-Sic-Graphite Hybrid Composites, International Symposium Of Research Students On Materials Science And Engineering December 20-22, 2004, Chennai, India
  98. Hai-Xia Guo and Jian-Feng Yang Fabrication and Tribological Properties of Mesocarbon Microbead-Cu Friction Composites Materials 2020, 13, 463
  99. Titus Thankachan, K. SooryaPrakash, “Microstructural, mechanical and tribological behavior of aluminum nitride reinforced copper surface composites fabricated through friction stir processing route”, Materials Science & Engineering, Vol. A 688, pp.301-308, 2017.
  100. Bhat and D. Bourell, “Tribological properties of metal matrix composite coatings produced by electrodeposition of copper”, Materials Science and Technology, VOL. 31 NO.8, pp. 969-674,2015.
  101. O. S. Fatoba, O. Popoola, “The Effects of Silicon Carbide Reinforcement on the Properties of Cu/SiCp Composites”, Silicon, DOI 10.1007/s12633-014-9199-x, 2014
  102. TejasUmale, Amarjit Singh, “Abrasive Wear BehaviourOf Copper-Sic And Copper-Sio2 Composites”, International Journal of Modern Physics: Conference Series, Vol. 22, pp. 416-423,2013.
  103. C. Siddaraju, H.S. Sunil Kumar, Praveennath G. Koppad, Nanohardness and Wear Behavior of Copper-SiC-CNTs Nanocomposites FME Transactions (2020) 48, 688-692
  104. Vishwanath Koti, Raji George, Ali Shakiba, K. V. Shivananda Murthy, Mechanical properties of Copper Nanocomposites Reinforced withUncoated and Nickel Coated Carbon Nanotubes FME Transactions (2018) 46, 623-630
  105. Mateusz W?sik and Joanna Karwan-Baczewska,Copper Metal Matrix Composites Reinforced by Titanium Nitride Particles,
  106. P.Yih and Chung,Titanium diboride coppr matrix composites,Journal of material science,1997,1703-1709.
  107. Smail Hamamda ,Ahmed Jari, and T. Avramenko Thermal Analysis of Copper-Titanium-Multiwall Carbon Nanotube Composites Nano reaserch letters.2017
  108. Izabela Firkowska, Andre Boden, Anna-Maria Vogt and Stephanie Reich Effect of carbon nanotube surface modification on thermal properties of copper-CNT composites J. Mater. Chem., 2011, 21, 17541-17546
  109. M.Sobhani. H.Arab, A.Mirhabibi, Microstructural Evolution of Copper-Titanium Alloy during In-situ Formation of TiB2 Particles , 2015Materials Science & Engineering, Vol. A 532, pp.301-308

International Journal of Scientific Research in Science, Engineering and Technology

Downloads

Published

2021-06-30

Issue

Volume 8, Issue 3, May-June-2021

Section

Research Articles

License

Copyright (c) IJSRSET

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

[1]
Dr. Ranjith V, Dr. H K Shivanand2, Dr. Tukaram Jadhav3, Verma R4, Puneeth P, " Evaluation of Mechanical Properties of Micro-Titanium and CNT Reinforced Copper Based MMC, International Journal of Scientific Research in Science, Engineering and Technology(IJSRSET), Print ISSN : 2395-1990, Online ISSN : 2394-4099, Volume 8, Issue 3, pp.81-104, May-June-2021. Available at doi : https://doi.org/10.32628/IJSRSET218315