Effect of Feed rate on Material Removal Rate, Surface Roughness and Machining Time of Aluminum Alloy 6063 in CNC Turning

Authors

  • P. Senthilkumar  Lecturer, Department of Mechanical Engineering, Valivalam Desikar Polytechnic College, Nagapattinam, Tamilnadu, India.
  • R. Senthilkumar  Lecturer, Department of Mechanical Engineering, P.A.C.Ramasamy Raja Polytechnic College, Rajapalayam, Tamilnadu, India.
  • B. Marichelvam  Lecturer, Department of Mechanical Engineering, P.A.C.Ramasamy Raja Polytechnic College, Rajapalayam, Tamilnadu, India.

DOI:

https://doi.org/10.32628/IJSRSET229518

Keywords:

Feed Rate, Material Removal Rate, Surface Roughness, Machining Time, Aluminum.

Abstract

The main objective of today’s manufacturing industries is to produce low cost and high quality product in short time. Turning is a very important machining process in which a single-point cutting tool removes material from the surface of a rotating cylindrical work-piece. In general, CNC lathe machine is operated with several controllable factors such as spindle speed, depth of cut, feed rate etc. This present work focuses on CNC turning of aluminum alloy 6063 using carbide tool for varying feed rate. The results revealed that the feed rate is the most important parameter that affects the material removal rate, surface finish and machine time in CNC turning process.

References

  1. Deepak D and Rajendra B, “Studies on material removal rate of Al 6061 while turning with coolant and without coolant using Taguchi method”, International Journal of Research in Engineering and Technology, Vol: 04 Issue: 09, 2015, pp.75-78.
  2. C. John Joshua and N. Rajakumar, “Effect of Spindle Speed and Feed Rate on Surface Roughness and Material Removal Rate of AA6063A in CNC Turning Using Response Surface Methodology”, International Journal of Research in Mechanical Engineering & Technology, Vol.5, Issue.2, 2015, pp.7-11.
  3. M. Sree Praveen Chowdary, SK. Waseem Sohail , SK. Sajidh and K. Sai Krishna, “Optimisation of surface roughness and material removal rate in turning operation of mild steel using Taguchi method”, International Journal of Engineering Sciences & Research Technology, 7(2), 2018, pp.477-484.
  4. Maske K.V. and Sawale J.K., “Study of Influence of Tool Nose Radius on Surface Roughness and Material Removal Rate in Turning of Inconel 718 by using Taguchi Grey Relational Analysis,” International Research Journal of Engineering and Technology, Vol: 04 Issue: 09, 2017, pp. 1148-1153.
  5. Palash Biswas, Arkadeep Bandyopadhyay, Anup Biswas, Shuvo Saha and Mihir Kumar Dey, “Study of Surface Roughness in CNC Milling Operation on 6061 Graded Aluminum Alloy”, International Journal of Engineering Research & Technology, NCETER - 2021 Conference Proceedings. Vol:9, Issue:11, pp.25-28, 2021
  6. Mahendra Korat and Neeraj Agarwal, “Optimization of Different Machining Parameters of En24 Alloy Steel In CNC Turning by Use of Taguchi Method”, International Journal of Engineering Research and Applications, Vol. 2, Issue 5, 2012, pp.160-164.
  7. T. S. Pawar, Dr. B. R. Borkar and Prof. V. B. Shinde, “Optimization of turning parameters to improve surface roughness of 2024-T3 aluminium”, IJARIIE, Vol-4 Issue-4 pp.658-664, 2018.
  8. Nithyanandhan.T , Manickaraj.K and Kannakumar.R, “Optimization of Cutting Forces, Tool Wear and Surface Finish in Machining of AISI 304 Stainless Steel Material Using Taguchi’s Method”, International Journal of Innovative Science, Engineering & Technology, Vol. 1, Issue 4, pp.488-493, 2014.
  9. M.V.R.D Prasad , G.Ranga janardhana and D. Hanumatha rao, “ Experimental Investigation To Study The Influence Of Process Parameters In Dry Machining”. APRN Journal Of Engineering And Applied Sciences, Vol. 4, No. 3, pp.91-94, 2009
  10. Swaraj Samanta, Sumit Kumar, Souram Guha and Sonal Kr. Singh, “Process parameters optimization of CNC turning on Al 6061 using multiple cutting fluids,” International Research Journal of Engineering and Technology, Vol: 05 Issue: 07, 2018, pp.1751-1757.
  11. Yakala Mani Ratnam, N Govindu and Vikas Ranjan, “Optimization of process parameters in CNC turning using RSM”, International journal of innovative research in technology, Vol: 3, Issue: 5, pp.284- 293, 2016.
  12. N. Satheesh Kumar, Ajay Shetty, Ashay Shetty, Ananth K, Harsha Shettya, “Effect of spindle speed and feed rate on surface roughness of Carbon Steels in CNC turning”, Procedia Engineering, 38, 2012, pp.691 – 697.
  13. J. Kouam, V. Songmene, M. Balazinski and P. Hendrick, “Dry, Semi-Dry and Wet Machining of 6061-T6 Aluminium Alloy”, Aluminium Alloys - New Trends in Fabrication and Applications, http://dx.doi.org/10.5772/51351
  14. M. Dhanenthiran , P. Naveenkumar, M. Mohamedsameer, A. Romario richard, and K. Ranjith Kumar, “Parameters of micro turning of aluminium rod Al 6063 using CNC machine”, International Journal of Engineering, Science and Mathematics, Vol. 7, Issue.4, 2018, pp. 231-241.
  15. Alagarsamy.S.V, Raveendran.P, Arockia Vincent Sagayaraj.S and Tamil Vendan.S, “Optimization of Machining Parameters for Turning of Aluminium Alloy 7075 using Taguchi Method”, International Research Journal of Engineering and Technology, Volume: 03 Issue: 01, pp.316-322, 2016

International Journal of Scientific Research in Science, Engineering and Technology

Downloads

Published

2022-10-30

Issue

Volume 9, Issue 5, September-October-2022

Section

Research Articles

License

Copyright (c) IJSRSET

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

[1]
P. Senthilkumar, R. Senthilkumar, B. Marichelvam "Effect of Feed rate on Material Removal Rate, Surface Roughness and Machining Time of Aluminum Alloy 6063 in CNC Turning" International Journal of Scientific Research in Science, Engineering and Technology (IJSRSET), Print ISSN : 2395-1990, Online ISSN : 2394-4099, Volume 9, Issue 5, pp.142-147, September-October-2022. Available at doi : https://doi.org/10.32628/IJSRSET229518