Review Paper on Optimal Robust Control of Contactless Breaking System Using Eddy Current System

Authors

  • Aakash Tandel  UG Student, Mechanical Department, Gujarat Technological University/Sigma Institute of engineering, Vadodara, Gujarat, India
  • Sagar Jyani  UG Student, Mechanical Department, Gujarat Technological University/Sigma Institute of engineering, Vadodara, Gujarat, India
  • Hardik Patel  UG Student, Mechanical Department, Gujarat Technological University/Sigma Institute of engineering, Vadodara, Gujarat, India
  • Parth Patel  UG Student, Mechanical Department, Gujarat Technological University/Sigma Institute of engineering, Vadodara, Gujarat, India
  • Mr. Twinkal M. Bhavsar  Assistant Professor, Mechanical Department, Sigma Institute of engineering, Vadodara, Gujarat, India

Keywords:

Friction, Breaking system, Eddy current

Abstract

A non-contact method, using magnetic drag force principle, was proposed to design the braking systems to improve the shortcomings of the conventional braking systems. The extensive literature detailing all aspects of the magnetic braking is briefly reviewed, however little of this refers specifically to upright magnetic braking system, which is useful for industries. One of the major issues to design upright magnetic system is to find out the magnetic flux. The changing magnetic flux induces eddy currents in the conductor. These currents dissipate energy in the conductor and generate drag force to slow down the motion. Therefore, a finite element model is developed to analyze the phenomena of magnetic flux density when air gap and materials of track are varied. The verification shows the predicted magnetic flux is within acceptable range with the measured value. The results will facilitate the design of magnetic braking systems.

References

  1. R. Limpert, Brake Design and Safety. Warrendale, PA: Society of Automotive Engineers, 1999.
  2. Robert Bosch GmbH, Bosch Automotive Handbook. Warrendale, PA: Society of Automotive Engineers, 2004.
  3. Telma. (2004, December). Nos Produits. [Online]. Available: www.telma.com.
  4. H. Sakamoto, “Design of permanent magnet type compact ECB retarder,” Society of Automotive Engineers #973228, pp. 19-25, 1997.
  5. H.P.R. Frederikse, “Properties of magnetic materials,” in CRC Handbook of Physics and Chemistry. New York: CRC Press, 1996.
  6. H.D. Wiederick, N. Gauthier, D.A.Campbell, and P. Rochon, “Magnetic braking: Simple theory and experiment,” American Journal of Physics, vol. 55, no. 6, pp. 5503, 1987.
  7. M.A. Heald, “Magnetic braking: Improved theory,” American Journal of Physics, vol. 56, no. 6, pp. 521-522, 1988.
  8. L.H. Cadwell, “Magnetic damping: Analysis of an eddy current brake using an airtrack,” American Journal of Physics, vol. 64, no. 7, pp. 917-923, 1996.
  9. E.R. Laithwaite, Induction Machines for Special Purposes.London: Newnes, 1966.
  10. J.H. Wouterse, “Critical torque and speed of eddy current brake with widely separated soft iron poles,” in IEE Proceedings-B vol. 138, no. 4, pp. 153-158, 1991.

International Journal of Scientific Research in Science, Engineering and Technology

Downloads

Published

2018-04-10

Issue

Volume 4, Issue 5, March-April-2018

Section

Research Articles

License

Copyright (c) IJSRSET

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

[1]
Aakash Tandel,Sagar Jyani,Hardik Patel,Parth Patel, Mr. Twinkal M. Bhavsar, " Review Paper on Optimal Robust Control of Contactless Breaking System Using Eddy Current System, International Journal of Scientific Research in Science, Engineering and Technology(IJSRSET), Print ISSN : 2395-1990, Online ISSN : 2394-4099, Volume 4, Issue 5, pp.612-614, March-April-2018.