Edge preparation of belt with belt grinding machine

Authors

  • Mr. Daxesh Makwana  Assistant Professor, Mechanical Department, Sigma Institute of Engineering, Vadodara, Gujarat, India
  • Mr. Nirav Saksena   Assistant Professor, Mechanical Department, Sigma Institute of Engineering, Vadodara, Gujarat, India
  • Mr. Ashvin Kapadiya  Assistant Professor, Mechanical Department, Sigma Institute of Engineering, Vadodara, Gujarat, India

Keywords:

Belt, Edge, Grinding Machine,Edge Preparation,Tapper Grinding

Abstract

Only in earlier days grinding of a belt for joining the two end of the belt is done. That requires hand on sanders machines which requires skill labour and can cause hazards to human. Due to inefficiency of human, human error will be there and rejection of belt can be occurs. Worker can not apply even pressure on the belt that might load to higher tolerance. With aim to minimize tolerance and user friendly work. We have obtained one solution for that to make a machine to have same ability of work. The work will be done on grinding wheel by putting belt at angle required according to the size of the belt and taper of the belt that will minimize human errors, efforts and any hazards to human. Due to lower in human error lower tolerance can be achieved.

References

  1. V B Bhandari, design of machine element, McGraw hill book compart 3rd edition.
  2. R B patil design of machine element first edition.
  3. R S khurmi and J K gupta A text book of machine design.
  4. marks standard handbook for mechanical engineering Bool by Ali M. sadgh and eudeneA.avallone.
  5. Analysis and Design of Machine Elements.
  6. Fundamental of machine component design, Books by Robert juvinall.
  7. Samuels, Leonard Ernest. Metallographic polishing by mechanical methods. Asm International, 2003.
  8. Samuels, Leonard Ernest. Metallographic polishing by mechanical methods. Asm International, 2003.
  9. Pappachan, Bobby K., et al. "Frequency Domain Analysis of Sensor Data for Event Classification in Real-Time Robot Assisted Deburring." Sensors 17.6 (2017): 1247
  10. WeiFeng, Department of Mechanical and Electrical Engineering, School of Physics and Mechanical & Electrical Engineering, XiamenUniversity,Xiamen361005,China
  11. BinYao,StateKeyLaboratoryforManufacturingandSystemsEngineering,Schoolof Mechanical Engineering ,Xi’an Jiaotong University, Xi’an710049,China
  12. Jae-Seob Kwak, Application of Taguchi and response surface methodologies for geometric error in surface grinding process, International Journal of Machine Tools and Manufacture, Volume45,Issue3, March2005, Pages327- 334
  13. Masuzawa, T., et al. "Wire electro-discharge grinding for micro-machining." CIRP Annals-Manufacturing Technology34.1 (1985): 431-434.
  14. Li, Z. C., Zhijian J. Pei, and Graham R. Fisher. "Simultaneous double side grinding of silicon wafers: a literature review." International Journal of Machine Tools and Manufacture46.12-13 (2006): 1449-1458.
  15. K. Nishio, Double-end surface grinding machine, US Patent 4,782,631, 1988.
  16. Aurich, Jan C., et al. "Modelling and simulation of process: machine interaction in grinding." Production Engineering 3.1 (2009): 111-120.

International Journal of Scientific Research in Science, Engineering and Technology

Downloads

Published

2018-04-10

Issue

Volume 4, Issue 5, March-April-2018

Section

Research Articles

License

Copyright (c) IJSRSET

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

[1]
Mr. Daxesh Makwana, Mr. Nirav Saksena , Mr. Ashvin Kapadiya "Edge preparation of belt with belt grinding machine" International Journal of Scientific Research in Science, Engineering and Technology (IJSRSET), Print ISSN : 2395-1990, Online ISSN : 2394-4099, Volume 4, Issue 5, pp.661-664, March-April-2018.