Faulty Lock Detection and Separation System

Authors

  • Mishra Nikhilkumar N  B.E. Student, Mechanical Engineering, Sir Visvesvaraya Institute of Technology, Nashik, Maharashtra, India
  • Madale Kabirdas N  B.E. Student, Mechanical Engineering, Sir Visvesvaraya Institute of Technology, Nashik, Maharashtra, India
  • Khairnar Pratik S  B.E. Student, Mechanical Engineering, Sir Visvesvaraya Institute of Technology, Nashik, Maharashtra, India
  • Sangale Prasad M  B.E. Student, Mechanical Engineering, Sir Visvesvaraya Institute of Technology, Nashik, Maharashtra, India
  • Ostwal Rishabh S  Assistant Professor, Mechanical Engineering, Sir Visvesvaraya Institute of Technology, Nashik, Maharashtra, India

DOI:

https://doi.org/10.32628/IJSRSET196113

Keywords:

Fault detection, Sensors, Motors, Fabrications.

Abstract

All product manufacturing units need to have a faulty product detection and separation system in order to maintain product quality and maintain a good reputation. So here we demonstrate such a system using a mini conveyer belt system. We propose to design and fabricate a faulty product detection and separation mechanism. Each product is different and thus has different mechanisms to detect faulty products. Here we detect fault in lock based on its size and operations. We use a sensor to detect each lock size and operations as products move over a conveyer belt. The conveyer is design so that it can hold the lock so that it does not fall or leave the conveyer belt. A defected product with size lower than minimum limit will be automatically detected as it moves on a conveyer belt and separated by a conveyer arm. If the product passes the size test the next sensor perform it task to operate the lock so that it can open the locking mechanism and check if it opens or not. If the product passes the test it is send for packaging and if not the product is separated and sent to production line for correct the fault. Here we use rollers and rubber belt to develop a mini conveyer belt mechanism. This mechanism is operated by a motor. This system uses servo motor arm to separate the faulty product.

References

  1. "Obstacle Detection Sensors: A Survey" Sachin Lalar Department of Computer Science & Engg, TERI, Kurukshetra, India Accepted 20 December 2013, Available online 31 December 2013, Vol.3, No.5 (December 2013).
  2. "Motion Detection Using PIR Sensor" Yogesh Pawar1, Abhay Chopde, Mandar Nandre Department of Electronics Engineering, Vishwakarma Institute of Technology, Pune.
  3. "Ultrasonic Distance Meter" Pawar Priti Arun, Mane Anjali Sudhakar, Pawar Megha Sunil, Sawant Shital Balaji Department of Electronics & Tele-Communication Engineering SVERI's College of Engineering, Pandharpur Academic Year: 2014 – 2015.
  4. "Robot Arm Control with Arduino" by Aimn Mohamed Ahmed Ghiet Spring 2017.
  5. "Working Principle of Arduino and using it as a Tool for Study and Research" Leo Louis1 1Department of Electronics and Communication Engineering, Gujarat Technological University, Ahmadabad, India.

International Journal of Scientific Research in Science, Engineering and Technology

Downloads

Published

2019-01-30

Issue

Volume 6, Issue 1, January-February-2019

Section

Research Articles

License

Copyright (c) IJSRSET

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

[1]
Mishra Nikhilkumar N, Madale Kabirdas N, Khairnar Pratik S, Sangale Prasad M, Ostwal Rishabh S "Faulty Lock Detection and Separation System" International Journal of Scientific Research in Science, Engineering and Technology (IJSRSET), Print ISSN : 2395-1990, Online ISSN : 2394-4099, Volume 6, Issue 1, pp.39-44, January-February-2019. Available at doi : https://doi.org/10.32628/IJSRSET196113